Datasheet Texas Instruments LMR64010

ManufacturerTexas Instruments
SeriesLMR64010
Datasheet Texas Instruments LMR64010

SIMPLE SWITCHERВ® 2.7V to 14V, 1A Step-Up Regulator in SOT-23 Package

Datasheets

LMR64010 SIMPLE SWITCHER ® 40Vout, 1A Step-Up Voltage Regulator in SOT-23 datasheet
PDF, 1.1 Mb, Revision: B, File published: Apr 4, 2013
Extract from the document

Prices

Status

LMR64010XMF/NOPBLMR64010XMFE/NOPBLMR64010XMFX/NOPB
Lifecycle StatusActive (Recommended for new designs)Active (Recommended for new designs)Active (Recommended for new designs)
Manufacture's Sample AvailabilityYesYesYes

Packaging

LMR64010XMF/NOPBLMR64010XMFE/NOPBLMR64010XMFX/NOPB
N123
Pin555
Package TypeDBVDBVDBV
Industry STD TermSOT-23SOT-23SOT-23
JEDEC CodeR-PDSO-GR-PDSO-GR-PDSO-G
Package QTY10002503000
CarrierLARGE T&RSMALL T&RLARGE T&R
Device MarkingSF9BSF9BSF9B
Width (mm)1.61.61.6
Length (mm)2.92.92.9
Thickness (mm)1.21.21.2
Pitch (mm).95.95.95
Max Height (mm)1.451.451.45
Mechanical DataDownloadDownloadDownload

Parametrics

Parameters / ModelsLMR64010XMF/NOPB
LMR64010XMF/NOPB
LMR64010XMFE/NOPB
LMR64010XMFE/NOPB
LMR64010XMFX/NOPB
LMR64010XMFX/NOPB
Duty Cycle(Max), %939393
Iq(Typ), mA2.12.12.1
Operating Temperature Range, C-40 to 125-40 to 125-40 to 125
Package GroupSOT-23SOT-23SOT-23
RatingCatalogCatalogCatalog
Regulated Outputs111
Special FeaturesEnableEnableEnable
Switch Current Limit(Min), A111
Switch Current Limit(Typ), A1.51.51.5
Switching Frequency(Max), kHz160016001600
Switching Frequency(Min), kHz160016001600
TypeConverterConverterConverter
Vin(Max), V141414
Vin(Min), V2.72.72.7
Vout(Max), V404040
Vout(Min), V333

Eco Plan

LMR64010XMF/NOPBLMR64010XMFE/NOPBLMR64010XMFX/NOPB
RoHSCompliantCompliantCompliant

Application Notes

  • Design of UVLO for LM27313 (Rev. B)
    PDF, 142 Kb, Revision: B, File published: Apr 8, 2014
  • AN-643 EMI/RFI Board Design (Rev. B)
    PDF, 742 Kb, Revision: B, File published: May 3, 2004
    Application Note 643 EMI/RFI Board Design
  • Working With Boost Converters
    PDF, 159 Kb, File published: Jun 15, 2015
    This brief note highlights some of the more common pitfalls when using boost regulators. These includemaximum achievable output current and voltage, short circuit behavior and basic layout issues. It isassumed that the reader is familiar with the basic operation of a boost regulator.
  • Input and Output Capacitor Selection
    PDF, 219 Kb, File published: Sep 19, 2005
  • Basic Calculation of a Boost Converter's Power Stage (Rev. C)
    PDF, 186 Kb, Revision: C, File published: Jan 8, 2014
    This application note gives the equations to calculate the power stage of a boost converter built with an IC with integrated switch and operating in continuous conduction mode. It is not intended to give details on the functionality of a boost converter (see Reference 1) or how to compensate a converter. See the references at the end of this document if more detail is needed.
  • AN-2155 Layout Tips for EMI Reduction in DC/ DC Converters (Rev. A)
    PDF, 3.6 Mb, Revision: A, File published: Apr 23, 2013
    This application note will explore how the layout of your DC/DC power supply can significantly affect theamount of EMI that it produces. It will discuss several variations of a layout analyze the results andprovide answers to some common EMI questions such whether or not to use a shielded inductor.
  • AN-1566 Techniques for Thermal Analysis of Switching Power Supply Designs (Rev. A)
    PDF, 1.4 Mb, Revision: A, File published: Apr 23, 2013
    This application note provides thermal power analysis techniques for analyzing the power IC.
  • AN-1889 How to Measure the Loop Transfer Function of Power Supplies (Rev. A)
    PDF, 2.7 Mb, Revision: A, File published: Apr 23, 2013
    This application report shows how to measure the critical points of a bode plot with only an audiogenerator (or simple signal generator) and an oscilloscope. The method is explained in an easy to followstep-by-step manner so that a power supply designer can start performing these measurements in a shortamount of time.
  • Semiconductor and IC Package Thermal Metrics (Rev. C)
    PDF, 201 Kb, Revision: C, File published: Apr 19, 2016
  • Inverted SEPIC Made SIMPLE
    PDF, 408 Kb, File published: Jul 31, 2015
    There can be quite a few applications that require a conversion from a negative input voltage to a negativeoutput voltage and there are a few ways to go about doing it. The telecom industry is one such examplewhere the rails are usually negative. This design space along with being limited is not well explored. In thisapplication note we will go over the use of an integrated boost regulator i
  • AN-1149 Layout Guidelines for Switching Power Supplies (Rev. C)
    PDF, 82 Kb, Revision: C, File published: Apr 23, 2013
    When designing a high frequency switching regulated power supply layout is very important. Using agood layout can solve many problems associated with these types of supplies. The problems due to a badlayout are often seen at high current levels and are usually more obvious at large input to output voltagedifferentials. Some of the main problems are loss of regulation at high output current
  • Understanding Boost Power Stages In Switchmode Power Supplies
    PDF, 149 Kb, File published: Mar 4, 1999
    A switching power supply consists of the power stage and the control circuit. The power stage performs the basic power conversion from the input voltage to the output voltage and includes switches and the output filter. This report addresses the boost power stage only and does not cover control circuits. The report includes detailed steady-stage and small-signal analysis of the boost power stage o
  • AN-1229 SIMPLE SWITCHER PCB Layout Guidelines (Rev. C)
    PDF, 374 Kb, Revision: C, File published: Apr 23, 2013
    This application report provides SIMPLE SWITCHER™ PCB layout guidelines.
  • AN-2162 Simple Success With Conducted EMI From DC-DC Converters (Rev. C)
    PDF, 2.5 Mb, Revision: C, File published: Apr 24, 2013
    Electromagnetic Interference (EMI) is an unwanted effect between two electrical systems as a result ofeither electromagnetic radiation or electromagnetic conduction. EMI is the major adverse effect caused bythe application of switch-mode power supplies (SMPS). In switching power supplies EMI noise isunavoidable due to the switching actions of the semiconductor devices and resulting disconti
  • AN-1520 A Guide to Board Layout for Best Thermal Resistance for Exposed Packages (Rev. B)
    PDF, 9.2 Mb, Revision: B, File published: Apr 23, 2013
    This thermal application report provides guidelines for the optimal board layout to achieve the best thermalresistance for exposed packages. The thermal resistance between junction-to-ambient (ОёJA) is highlydependent on the PCB (Printed Circuit Board) design factors. This becomes more critical for packageshaving very low thermal resistance between junction-to-case such as exposed pad TSSOP

Model Line

Manufacturer's Classification

  • Semiconductors> Power Management> Non-isolated DC/DC Switching Regulator> Step-Up (Boost)> Boost Converter (Integrated Switch)
EMS supplier