RadioLocman.com Electronics ru
Advanced Search +
  
Go Back   RadioLocman Forum > Electronics and ... > Beginners

Beginners Questions from beginners.

Reply
 
Thread Tools Search this Thread
Old 07-29-2016, 09:21 AM   #1
April155
Junior Member
 
Join Date: Jul 2016
Posts: 4
April155 is on a distinguished road
Default Problem of building an AM radio need advice !

Hello, everyone in here. Very glad that i can post my questions here to get your help.
I have been following the tutorial below to build an AM radio, and when powered on I was picking up what id presume to be radio waves (what I'd describe as a mishmash of "whooshing" sporadic oscillations).
http://www.instructables.com/id/Simple-OP-Amp-radio/
Alright all I need for this project are the following:

x1 LM386 op amp IC chip (From http://www.kynix.com/Detail/1267823/...-4%2FNOPB.html)
x2 1000 microfarad capacitors (any capacitor works but it's louder with these)
x1 100 microfarad capacitor
x1 8 ohm speaker
x1 9 volt battery
x1 project board
some wire (I used about a foot and a half)

optional - a wire parabola (such as a mini fan cage, a colander, etc.)

This was great, but I wanted to single out a specific frequency and listen to a radio station. I did some research and figured out that I have to add a resonance circuit called an LC circuit to single out specific frequencies. I made one with a variable inductor I made with 47 coils in 10cm with square steel railroad spike of diameter 1.5 cm in the center and a capacitor like below. I experimented with 220 pF capacitors in parallel to make 220, 440, and 660 pF and tried using my variable inductor to tune into a station for each of them but it did not work.


(apologize for the poor drawing)
I chose that coil count using the following equation to tune into mid freq radio singles (535-1500 khz), I made sure it covered the lowest frequency and then I could shorten it to get the higher frequencies.:

At this point I was stumped, I heard that you had to put a diode in to single out high frequency singles so desperate, I inserted it between pin 3 and my LC circuit but it didn't help. I also made a home made variable capacitor but likewise I coundn't tune into a station. Most importantly I heard you had to ground the circuit so I attached a wire for the tuner circuit to my computer(which is ground) and it changed the tone slightly but still couldn't tune into a station.
I started to wonder whether there were any am stations in my area due to its falling popularity, but a quick test with my mother's car radio yielded handful of them.
I apologize if my troubleshooting may seem stupid but I'm a little new to this circuit building stuff. I Thank you for reading thus far, and I appreciate any assistance you guys may offer.
Attached Images
File Type: png circuit.png (474.2 KB, 0 views)
April155 is offline   Reply With Quote
Reply

Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
PIC32 MX795F512L - ADC problem vdurgaidass Microcontrollers (MCU) 1 03-27-2016 11:29 AM
LCD 16x2 LCD display problem PIC 16f887 Momoatomic Microcontrollers (MCU) 1 03-04-2016 10:01 AM
Radio receiver on a chip TDA7000 mark Beginners 2 11-22-2013 12:56 PM
Easy PicV7 advice captain Projects and Advices 0 04-21-2012 10:22 AM

All times are GMT. The time now is 10:34 AM.




Powered by vBulletin® Version 3.8.8
Copyright ©2000 - 2017, vBulletin Solutions, Inc.
Slices ↓
Radiolocman facebook Radiolocman twitter Radiolocman google plus