RadioLocman.com Electronics ru
Advanced Search +
  

universal USB interfaced programmer Elnec BeeProg2C

Elnec » BeeProg2C, PROG BeeProg2C

Main Features of Programmer
ParameterValue
Type
  • In-circuit
  • Autonomous
Connection interface
  • USB
  • LPT
Target connection
  • ISP
  • ZIF socket
Versiondesktop
Supported devices
  • MCU Atmel AVR
  • MCU Atmel ARM
  • MCU Atmel 8051
  • MCU Microchip PIC
  • MCU TI MSP430
  • MCU Motorola
  • MCU ST8L
  • MCU ST8S
  • MCU STM32
  • Flash
  • EPROM
  • EEPROM
  • serial EEPROM
  • serial DataFlash
  • PLD
  • OTP EPROM

Extremely fast universal USB interfaced programmer. Cost effective version of BeeProg2 programmer (differences see below). If you need to program some of the mentioned devices, see BeeProg2 programmer.

Short description:

  • 73973 supported devices from 293 manufacturers by 2.98 version of SW (16. May. 2013)
  • extremely fast programming, one of the fastest programmers in this category. Programs 64-Mbit NOR Flash memory less than 9 seconds and 1Gbit NAND Flash less than 70 sec.
  • 48-pins powerful pindrivers, no adapter required for any DIL devices
  • ISP connector for in-circuit programming
  • connection to PC: USB 2.0 (up to 480 Mbit/s, high speed/full speed) and 1.1 compatible interface
  • after upgrade to BeeProg2, also high-speed IEEE 1284 (ECP/EPP) printer-port (LPT) interface is available
  • comfortable and easy to use control program, work with all versions of MS Windows from Windows 2000 to Windows 8 (32 and 64-bit)
  • unique quick reaction to customer's needs - software update can be ready within a day from request by OnDemand software
  • Multiprogramming possible by attaching more programmers to one PC
  • approved by CE laboratory to meet CE requirements
  • made in Slovakia
  • warranty - 3 years

Features

  • GENERAL
    • BeeProg2C is USB-compatible, MS Windows (from Windows 2000 to Windows 8 32-bit and 64-bit) based ELNEC universal programmers, built to meet the strong demand of the small manufacturing and developers community for the fast and reliable universal programmer.
    • BeeProg2C programmer have hardware identical with the BeeProg2 programmer, the differences are only in software. BeeProg2C have next limitations against BeeProg2:
      • unsupported obsolete bipolar chips (PROMs and PLDs)
      • unsupported obsolete EPROMs with programming voltage 21V and above
      • unsupported obsolete 2708 EPROMs
      • unsupported obsolete microcontrollers MCS48 series
      • unsupported obsolete microcontrollers 8751/8752 with programming voltage 21V and above
      • LPT port connection usage is disabled in software
    • BeeProg2C programmer can be any time upgraded to BeeProg2 using BeeProg2C to BeeProg2 upgrade kit
    • Supports all kinds of types and silicon technologies of today and tomorrow programmable devices without family-specific module. You have freedom to choose the optimal device for your design. Using built-in in-circuit serial programming (ISP) connector, the programmer is able to program ISP capable chips in circuit.
    • BeeProg2C isn't only a programmer, but also a tester of TTL/CMOS logic ICs and memories. Furthermore, it allows generation of user-definable test pattern sequences.
    • Provides very competitive price coupled with excellent hardware design for reliable programming.
    • Extremely fast programming due to high-speed FPGA driven hardware and execution of time-critical routines inside of the programmer. As a result, when used in production this one-socket-programmer waits for an operator, and not the other way round.
    • BeeProg2C interfaces with the IBM PC compatible or higher, portable or desktop personal computers through USB (2.0/1.1) port. After upgrade to BeeProg2 can be also used parallel (printer) port.
  • HARDWARE
    •     FPGA based totally reconfigurable 48 powerful TTL pindrivers provide H/L/pull_up/pull_down and read capability for each pin of socket. Advanced pindrivers incorporate high-quality high-speed circuitry to deliver signals without overshoot or ground bounce for all supported devices. Improved pin drivers drivers operate down to 1.8V so you'll be ready to program the full range of today's advanced low-voltage devices.
    •     The programmer performs device insertion test (wrong or backward position) and contact check (poor contact pin-to-socket) before it programs each device. These capabilities, supported by overcurrent protection and signature-byte check help prevent chip damage due to operator error.
    •     The selftest capability allow to run diagnostic part of software to thoroughly check the health of the programmer.
    •     Built-in protection circuits eliminate damage of programmer and/or programmed device due to environment or operator failure. All the inputs of the BeeProg2C programmer, including the ZIF socket, connection to PC and power supply input, are protected against ESD up to 15kV.
    •     BeeProg2C programmer performs programming verification at the marginal level of supply voltage, which, obviously, improves programming yield, and guarantees long data retention.
    •     Various programming adapters are available to handle device in PLCC, JLCC, SOIC, SDIP, SOP, PSOP, SSOP, TSOP, TSOPII, TSSOP, QFP, PQFP, TQFP, VQFP, QFN (MLF), SON, BGA, EBGA, FBGA, VFBGA, UBGA, FTBGA, LAP, CSP, SCSP, LQFP, MQFP, HVQFN, QLP, QIP and other packages.
  • SOFTWARE
    •     Programmer is driven by an easy-to-use control program with pull-down menu, hot keys and on-line help. Selecting of device is performed by its class, by manufacturer or simply by typing a fragment of vendor name and/or part number.
    •     Standard device-related commands (read, blank check, program, verify, erase) are boosted by some test functions (insertion test, signature-byte check), and some special functions (autoincrement, production mode - start immediately after insertion of chip into socket).
    •     All known data formats are supported. Automatic file format detection and conversion during loading of file.
    •     The rich-featured auto-increment function enables one to assign individual serial numbers to each programmed device - or simply increments a serial number, or the function enables one to read serial numbers or any programmed device identification signatures from a file.
    •     The software also provide a many information about programmed device. As a special, the drawing of all available packages are provided. The software provide also explanation of chip labelling (the meaning of prefixes and suffixes at the chips) for each supported chip.
    •     The software provide a full information for ISP implementation: Description of ISP connector pins for currently selected chip, recommended target design around in-circuit programmed chip and other necessary information.
    •     The remote control feature allows to be PG4UW software flow controlled by other application – either using .BAT file commands or using DLL file. DLL file, examples (C/PAS/VBASIC/.NET) and manual are part of standard software delivery.
    •     Jam files of JEDEC standard JESD-71 are interpreted by Jam Player. Jam files are generated by design software which is provided by manufacturer of respective programmable device. Chips are programmed in-ZIF or through ISP connector (IEEE 1149.1 Joint Test Action Group (JTAG) interface).
    •     VME files are interpreted by VME Player. VME file is a compressed binary variation of SVF file and contains high-level IEEE 1149.1 bus operations. SVF files are interpreted by SVF Player. SVF file (Serial Vector Format) contains high-level IEEE 1149.1 bus operations. SVF files are generated by design software which is provided by manufacturer of respective programmable device. Chips are programmed in-ZIF or through ISP connector (IEEE 1149.1 Joint Test Action Group (JTAG) interface). VME files are generated by design software which is provided by manufacturer of respective programmable device. Chips are programmed in-ZIF or through ISP connector (IEEE 1149.1 Joint Test Action Group (JTAG) interface).
    •     Multiple devices are possible to program and test via JTAG chain: JTAG chain (ISP-Jam), JTAG chain (ISP-VME), JTAG chain (ISP-SVF) or JTAG chain (ISP-STP).
    •     Attaching of more BeeProg2C programmers to the same PC (through USB port) is achieved a powerful multiprogramming system, which support as many chips, as are supported by BeeProg2C programmer and without obvious decreasing of programming speed. It is important to know, there is a concurrent multiprogramming - each programmer works independently and each programmer can program different chip, if necessary.

 

Slices ↓
Radiolocman facebook Radiolocman twitter Radiolocman google plus