RadioLocman.com Electronics ru
Advanced Search +
  
» Advanced Technologies
» Analogue Design
» Antique
» Application Notes
» Audio
» Auto-Audio
» Automation
» Automotive
» Bad Prescriptions
» Beginners
» CAD & Software
» Camcorders
» Cellular
» Computers and Peripherals
» Digital
» Domestic
» Games
» High Voltage
» Interfaces
» Laser
» Light
» MCU open-source platforms
» Measurement
» Medicine
» Microcontrollers usage
» Monitors
» Music
» Networks
» Oscillators
» Power
» Radio
» RC Modeling
» Robots
» Satellite
» Security
» Solar
» Supply
» Telephone
» Theory
» Tools and Technologies
» TV
» Video
» Wind Energy
» Wireless
Search results: 229   Output: 61-70
  1. Mike Wong, Intersil EDN Assume that a design requires positive voltage, but only a negative-voltage power source is available. Using a standard boost-converter IC in the circuit of Figure 1, you can efficiently generate a positive voltage from a ...
    Circuits » Supply · Power » EL7515
    11-11-2015
  2. Mike Rose EDN Using the fast dynamic load described in this Design Idea to test the transient response of a power system can reveal many critical operating characteristics. The voltage deviation resulting from a fast current step can provide ...
    04-11-2015
  3. Tom Gross, Linear Technology Design Note 511 Introduction The LTC3626 synchronous buck regulator with current and temperature monitoring is the first of Linear’s SWITCHER+™ line of monolithic regulators. It is a high efficiency, ...
    04-11-2015
  4. Ilija Uzelac EDN This Design Idea presents a simple, proven, reliable, and robust method for charging large capacitor banks, using a series connection of power MOSFETs to raise the breakdown voltage over that of an individual MOSFET. When a power ...
    Circuits » Supply · Power » IXTQ10P50P
    22-10-2015
  5. Susanne Nell EDN To measure high levels of direct current for overload detection and protection, designers frequently use either a current-shunt resistor or a toroidal core and Hall-effect magnetic-field sensor. Both methods suffer from drawbacks. ...
    22-10-2015
  6. Philip Karantzalis, Linear Technology Design Note 529 Introduction A common problem in power distribution systems is loss of regulation due to the cable/wire voltage drop between the regulator and the load. Any increase in wire resistance, cable ...
    Circuits » Supply · Power » Linear Technology » LT6110, LT3080, LT3976
    20-10-2015
  7. Vladimir Rentyuk EDN Most engineers know that they can use an inexpensive, three-terminal adjustable regulator, such as Fairchild Semiconductor’s LM317 , as an adjustable regulator to only some necessary value of voltage, such as 36 or 3 V. ...
    Circuits » Supply · Power » Fairchild » LM317
    13-10-2015
  8. Sajjad Haidar Electronic Design When a MOSFET or IGBT gate-threshold voltage is higher than the available drive voltage, it's standard to use an op amp or other driver to bridge the difference. This circuit uses a basic optocoupler plus a few ...
    Circuits » Analogue Design · Power » TPL191B
    30-09-2015
  9. Vladimir Rentyuk EDN A TL431 shunt regulator is a perfect choice for many applications. You can use it as a comparator with hysteresis by taking advantage of its inner voltage reference along with few additional components. You can use this ...
    Circuits » Supply · Power » TL431
    17-09-2015
  10. Todor Arsenov EDN Most isolated, offline SMPSs (switched-mode power supplies), including flyback, forward, and resonant, must operate at input voltages of 90 to 260 V rms. Some cases even use line-to-line voltages of 400 V rms 10%, leading to ...
    01-09-2015
 Pages:

Slices ↓
Radiolocman facebook Radiolocman twitter Radiolocman google plus