Datasheet Texas Instruments LM5022MM
| Manufacturer | Texas Instruments |
| Series | LM5022 |
| Part Number | LM5022MM |
6-60V Wide Vin, Current Mode Boost and SEPIC Controller 10-VSSOP -40 to 125
Datasheets
LM5022 60-V Low-Side Controller for Boost and SEPIC datasheet
PDF, 1.5 Mb, Revision: H, File published: Dec 16, 2016
Extract from the document
Prices
Status
| Lifecycle Status | NRND (Not recommended for new designs) |
| Manufacture's Sample Availability | No |
Packaging
| Pin | 10 |
| Package Type | DGS |
| Industry STD Term | VSSOP |
| JEDEC Code | S-PDSO-G |
| Package QTY | 1000 |
| Carrier | SMALL T&R |
| Device Marking | 5022 |
| Width (mm) | 3 |
| Length (mm) | 3 |
| Thickness (mm) | 1.02 |
| Pitch (mm) | .5 |
| Max Height (mm) | 1.07 |
| Mechanical Data | Download |
Replacements
| Replacement | LM5022MM/NOPB |
| Replacement Code | S |
Parametrics
| Duty Cycle(Max) | 90 % |
| Iout(Max) | 10 A |
| Iq(Typ) | 3.5 mA |
| Operating Temperature Range | -40 to 125 C |
| Package Group | VSSOP |
| Rating | Catalog |
| Regulated Outputs | 1 |
| Special Features | Enable,Frequency Synchronization,UVLO Adjustable |
| Switch Current Limit(Typ) | 10 A |
| Switching Frequency(Max) | 1000 kHz |
| Switching Frequency(Min) | 170 kHz |
| Type | Controller |
| Vin(Max) | 60 V |
| Vin(Min) | 6 V |
| Vout(Max) | 300 V |
| Vout(Min) | 1.25 V |
Eco Plan
| RoHS | See ti.com |
Design Kits & Evaluation Modules
- Evaluation Modules & Boards: LM5022EVAL
60V Wide Vin Low Side Controller for Boost Evaluation Board
Lifecycle Status: Active (Recommended for new designs)
Application Notes
- Driving LEDs: To Cap or Not to CapPDF, 542 Kb, File published: Mar 21, 2007
- AN-1696 Designing a Boost LED Driver Using the LM5022 (Rev. B)PDF, 238 Kb, Revision: B, File published: May 6, 2013
This application report provides a component-by-component design guide for a boost converter-basedLED driver using the LM5022. - Demystifying Type II and Type III Compensators Using Op-Amp and OTA for DC/DC CoPDF, 782 Kb, File published: Jul 11, 2014
- AN-1656 Design Challenges of Switching LED Drivers (Rev. A)PDF, 171 Kb, Revision: A, File published: May 3, 2013
Using a switching regulator as an LED driver requires the designer to convert a voltage regulator into acurrent regulator. Beyond the challenge of changing the feedback system to control current, the LEDsthemselves present a load characteristic that is much different than the digital devices and other loads thatrequire constant voltage. The LED WEBENCHВ® online design environment predicts and
Model Line
Series: LM5022 (4)
- LM5022MM LM5022MM/NOPB LM5022MME/NOPB LM5022MMX/NOPB
Manufacturer's Classification
- Semiconductors > Power Management > Non-isolated DC/DC Switching Regulator > Step-Up (Boost) > Boost Controller (External Switch)
