Datasheet LT1795 (Analog Devices) - 3

ManufacturerAnalog Devices
DescriptionDual 500mA/50MHz Current Feedback Line Driver Amplifier
Pages / Page12 / 3 — ELECTRICAL CHARACTERISTICS The
File Format / SizePDF / 158 Kb
Document LanguageEnglish

ELECTRICAL CHARACTERISTICS The

ELECTRICAL CHARACTERISTICS The

Model Line for this Datasheet

Text Version of Document

LT1795
ELECTRICAL CHARACTERISTICS The

denotes the specifications which apply over the full specified temperature range, otherwise specifications are at TA = 25
°
C. VCM = 0V,
±
5V

VS
≤ ±
15V, pulse tested, VSHDN = 2.5V, VSHDNREF = 0V unless otherwise noted. (Note 3) SYMBOL PARAMETER CONDITIONS MIN TYP MAX UNITS
R + IN Input Resistance VIN = ±12V, VS = ±15V ● 1.5 10 MΩ V = ±2V, VS = ±5V ● 0.5 5 MΩ C + IN Input Capacitance VIN = ±15V 2 pF Input Voltage Range (Note 5) VS = ±15V ● ±12 ±13.5 V VS = ±5V ● ±2 ±3.5 V CMRR Common Mode Rejection Ratio VS = ±15V, VCM = ±12V ● 55 62 dB VS = ±5V, VCM = ±2V ● 50 60 dB Inverting Input Current VS = ±15V, VCM = ±12V ● 1 10 µA/V Common Mode Rejection VS = ±5V, VCM = ±2V ● 1 10 µA/V PSRR Power Supply Rejection Ratio VS = ±5V to ±15V ● 60 77 dB Noninverting Input Current VS = ±5V to ±15V ● 30 500 nA/V Power Supply Rejection Inverting Input Current VS = ±5V to ±15V ● 1 5 µA/V Power Supply Rejection AV Large-Signal Voltage Gain VS = ±15V, VOUT = ±10V, RL = 25Ω ● 55 68 dB VS = ±5V, VOUT = ±2V, RL = 12Ω ● 55 68 dB R – OL Transresistance, ∆VOUT/∆IIN VS = ±15V, VOUT = ±10V, RL = 25Ω ● 75 200 kΩ VS = ±5V, VOUT = ±2V, RL = 12Ω ● 75 200 kΩ VOUT Maximum Output Voltage Swing VS = ±15V, RL = 25Ω ±11.5 ±12.5 V ● ±10.0 ±11.5 V VS = ±5V, RL = 12Ω ±2.5 ±3 V ● ±2.0 ±3 V IOUT Maximum Output Current VS = ±15V, RL = 1Ω ● 0.5 1 A IS Supply Current Per Amplifier VS = ±15V, VSHDN = 2.5V 29 34 mA ● 42 mA Supply Current Per Amplifier, VS = ±15V 15 20 mA RSHDN = 51k, (Note 6) ● 25 mA Positive Supply Current, Shutdown VS = ±15V, VSHDN = 0.4V ● 1 200 µA Output Leakage Current, Shutdown VS = ±15V, VSHDN = 0.4V 1 200 µA Channel Separation VS = ±15V, VOUT = ±10V, RL = 25Ω 80 110 dB HD2, HD3 2nd and 3rd Harmonic Distortion f = 1MHz, VO = 20VP-P, RL = 50, AV = 2 –75 dBc Differential Mode SR Slew Rate (Note 7) AV = 4, RL = 400Ω 400 900 V/µs Slew Rate AV = 4, RL = 25Ω 900 V/µs BW Small-Signal BW AV = 2, VS = ±15V, Peaking ≤ 1.5dB 65 MHz RF = RG = 910Ω, RL = 100Ω AV = 2, VS = ±15V, Peaking ≤ 1.5dB 50 MHz RF = RG = 820Ω, RL = 25Ω
Note 1:
Absolute Maximum Ratings are those values beyond which the life
Note 4:
Thermal resistance varies depending upon the amount of PC board of a device may be impaired. metal attached to the device. If the maximum dissipation of the package is
Note 2:
Applies to short-circuits to ground only. A short-circuit between exceeded, the device will go into thermal shutdown and be protected. the output and either supply may permanently damage the part when
Note 5:
Guaranteed by the CMRR tests. operated on supplies greater than ±10V.
Note 6:
RSHDN is connected between the SHDN pin and V+.
Note 3:
The LT1795C is guaranteed to meet specified performance from
Note 7:
Slew rate is measured at ±5V on a ±10V output signal while 0°C to 70°C and is designed, characterized and expected to meet these operating on ±15V supplies with RF = 1k, RG = 333Ω (AV = +4) and extended temperature limits, but is not tested at – 40°C and 85°C. The RL = 400Ω. LT1795I is guaranteed to meet the extended temperature limits. 1795fa 3