Starter Kit Keil MCBSTM32F400UME

Detailed Description

MCBSTM32F200UME - Starter kit which includes the ULINK-ME debug adapter and MCBSTM32F400 evaluation board.

The Keil MCBSTM32F400 Evaluation Board enables you to create and test working programs based on the STMicroelectronics STM32 F4xx series of ARM Cortex-M4 processor-based devices.

Features:

• 168 MHz STM32F407IG ARM Cortex-M4 processor-based MCU in 176-pin BGA
• On-Chip Memory: 1 MB Flash & 192 KB RAM
• External Memory: 8 MB NOR Flash, 512MB NAND Flash, 2 MB SRAM, 8 KB I2C EEPROM with NFC interface
• 2.4 inch Color QVGA TFT LCD with resistive touchscreen
• 10/100 Ethernet Port
• USB 2.0 Full Speed - USB, USB-OTG, & USB Host
• USB 2.0 High Speed - USB, USB-OTG, & USB Host
• 1 CAN Interface
• Serial/UART Port
• MicroSD Card Interface
• 5-position Joystick
• 3-axis digital Accelerometer
• 3-axis digital Gyroscope
• Analog Voltage Control for ADC Input (potentiometer)
• Audio CODEC with Line-In/Out and Speaker/Microphone
• Digital Microphone
• Digital VGA Camera
• Push-Buttons for Reset, Wakeup, Tamper and User
• 8 LEDs directly connected to port pins
• Power Supply via:
  • High Speed and Full Speed USB (micro) connectors
  • Power jack (8V-12V) with Voltage Regulator capable to supply both USB host interfaces (500mA each)
• Debug Interface Connectors
  • 20 pin JTAG (0.1 inch connector)
  • 10 pin Cortex debug (0.05 inch connector)
  • 20-pin Cortex debug + ETM Trace (0.05 inch connector)

Features

• Serial Port: A standard DB9 connector is on the board for the STM32F407's built-in UART interfaces.

  This is a full duplex, serial port.

• CAN Port: A standard DB9 connector for applications requiring CAN communications.
• USB 2.0 Full Speed and High Speed Ports: 2 standard USB Type mini-B connectors: One for full-speed and one for high-speed USB Device, Host and OTG communications.
• 100/10M Ethernet Port: A standard RJ45 connector on the MCBSTM32F400 board connects to an on-board Ethernet transceiver for applications requiring Ethernet communications.
• VGA Camera and Microphone: A 640×480 Color CMOS camera and on-board digital microphone for VGA image and digital sound capture.
• LCD Display with Touch Screen: A detachable, 240×320 TFT, color LCD display with 4-wire, resistive touch screen. You may use this graphic display device to show real-time debug and program status messages.
• Stereo CODEC and Amplifier and On-board Microphone: A low-power stereo CODEC with headphone and microphone amplifier. You may use this on-board device for audio applications.
• Motion Detectors: Both a low-power, 3-axis accelerometer and a 3-axis MEMS inertial rate sensor(gyroscope). You may use these on-board devices for applications requiring the detection of movement.
• On-board Battery: A removable, lithium battery is included on the MCBSTM32F400 to maintain power to the real-time clock when the board disconnects from the main power supply.
• Analog Voltage Control for ADC Input: An adjustable analog voltage source for testing the Analog to Digital converter built into the STM32F407 device.
• MicroSD Card Connector: A MicroSD Card connector for developing applications requiring access to MicroSD Cards.
• JTAG and Cortex/ETM Download and Debug: The MCBSTM32F400 board incorporates both a JTAG interface and a Cortex Debug + ETM interface.  When coupled with the ULINK2 USB-JTAG adapter, the Serial Wire JTAG interface allows flash programming and debugging.  With the ULINKPro adapter, the Cortex Debug/ETM interface allows flash programming and instruction trace debugging.

Evaluation Software

The MCBSTM32F400 Evaluation Board and Starter Kit include the MDK-Lite development tools. These tools help you get started writing programs and testing the microcontroller and its capabilities. Sample applications that run on the MCBSTM32F400 and a Quickstart guide are included.

The MCBSTM32F400UME Starter Kit includes:

1. The MCBSTM32F400 Evaluation Board.
2. ULINK-ME Debug adapter
3. MDK-ARM Lite Edition

MCBSTM32F400 Schematic Diagram