Evaluation Kit Texas Instruments HSDC-SEK-10

Detailed Description

These tools include a pattern capture card, pattern generator card, low jitter clock source, clean signal source, and a multi-output regulated power supply. They are simple to use, easily portable and require only one 110-120 VAC source for power.

TSW1405EVM - Low Cost Data Capture Card Features

• Simple 16-bit waveform capture from many of TI’s high speed ADC EVM’s
• Supports 64k sample depth at up to 1.0 GSPS LVDS I/O rates
• LatticeECP3 high speed mini FPGA
• Analyzes up to 8 channels concurrently
• Single mini USB cable for power and data
• Utilizes an intuitive/easy-to-use GUI package
• Industry’s lowest-cost high speed ADC evaluation platform

The TSW1406EVM is a low cost pattern generator circuit board used to evaluate some of Texas Instruments’ (TI) most popular high speed digital-to-analog converters (DAC).

TSW1406EVM Features

• Simple 16-bit waveform generation for use with TI’s high speed DAC EVM’s
• Supports 64k sample depth at up to 1.0 GSPS LVDS I/O rates
• LatticeECP3 high speed mini FPGA
• Analyzes up to 8 channels concurrently
• Single mini USB cable for power and data
• Utilizes easy to use software GUI package

The TSW4806 Evaluation Module uses a LMK04806 device, the industry's highest performance clock conditioner with superior clock jitter cleaning, generation, and distribution with advanced features to meet next generation system requirements. The dual loop PLL architecture enables very low jitter when used with a low noise VCXO reference source.

TSW4806 Features

• Multi-mode: Dual PLL, single PLL, and clock distribution
• Dual Loop PLLatinum PLL Architecture
• PLL1
  • Holdover mode when input clocks are lost
  • Automatic or manual triggering/recovery
• PLL2
  • Integrated Low-Noise VCO
• 50% duty cycle output divides, 1 to 1045 (even and odd)
• LVPECL, LVDS, or LVCMOS programmable outputs
• Precision digital delay, fixed or dynamically adjustable
• 25 ps step analog delay control
• 2 differential outputs
• 4 single-ended outputs
• 0-delay mode
• On board 10MHz reference oscillator
• User friendly Graphical User Interface (GUI)

The TSW2200EVM is a portable power supply based on TPS40055 switcher, TPS76xx LDOs and UCD90120A sequencer. The TSW2200 is designed to be powered from DC power ranging from 10-20V on 1 of 3 inputs: the included 12V wall supply, standard banana jack inputs, or a 19V power supply with 2.5mm ID × 5.5mm OD × 9.5mm DC jack found on some common laptop supplies. There are dedicated supplies for 1.8V, 3.3V, 5V, and 2 adjustable supplies from 1.4V to 6.37V all capable of providing 1A each. There is also a -5V supply capable of delivering 0.36A. An on board sequencer is provided to allow the supplies to be enabled in a predetermined time interval. This EVM can be used to deliver power to the other Low Cost Evaluation Tools as well as the ADC and DAC device EVMs.

TSW2200EVM Features

• Dedicated 1.8V, 3.3V, 5V @ 1A
• 2x adjustable 1.4V to 6.37V @ 1A
• A -5V supply @ 0.36A
• Includes 12V supply to power the board
• Ability to time sequence all of the supplies relative to each other
• Included GUI to manage sequencing if desired

The TSW2110EVM is a very clean 10 MHz source designed for the purposes of providing an input signal for testing TI ADC devices. The EVM includes a 10MHz crystal oscillator, an amplifier and a 10MHz Crystal filter with 16kHz band pass response. The output of the TSW2110EVM is set to about 10dBm, approximately 2Vpp, with typical harmonic performance greater than 80dBc. This is the appropriate peak to peak swing required by most TI ADCs. The TSW2110 can be easily powered from a 5V source such as a lab supply or from the 5V source of the TSW2200EVM (Low Cost Portable Power Supply).

TSW2110EVM Features

• Requires single 5V supply
• Onboard 10M crystal oscillator
• Onboard amplifier
• Onboard 10M crystal filter
• Harmonic performance better than 80dBc
• 2Vpp output level, direct connects to TI ADC EVMs for analysis

ti.com

Other Names:

HSDCSEK10, HSDC SEK 10