Datasheet Texas Instruments CC1101-Q1
| Manufacturer | Texas Instruments |
| Series | CC1101-Q1 |
Low-Cost Low-Power Sub-1-GHz RF Transceiver
Datasheets
Low-Power Sub-1-GHz Fractional-N UHF Device Family for Automotive datasheet
PDF, 1.6 Mb, Revision: B, File published: Apr 16, 2010
Extract from the document
Prices
Status
| CC1101QRHBRG4Q1 | |
|---|---|
| Lifecycle Status | Active (Recommended for new designs) |
| Manufacture's Sample Availability | No |
Packaging
| CC1101QRHBRG4Q1 | |
|---|---|
| N | 1 |
| Pin | 32 |
| Package Type | RHB |
| Industry STD Term | VQFN |
| JEDEC Code | S-PQFP-N |
| Package QTY | 3000 |
| Device Marking | QQ1 |
| Width (mm) | 5 |
| Length (mm) | 5 |
| Thickness (mm) | .9 |
| Pitch (mm) | .5 |
| Max Height (mm) | 1 |
| Mechanical Data | Download |
Parametrics
| Parameters / Models | CC1101QRHBRG4Q1 |
|---|---|
| Data Rate(Max), kbps | 250 |
| Device Type | UHF Transceiver |
| Frequency Bands, MHz | 315,433,779,868,915,920 |
| Operating Temperature Range, C | -40 to 125 |
| RX Current (Lowest), mA | 15.5 |
| Rating | Automotive |
| Sensitivity (Best), dBm | -114 |
| Special Features | AEC-Q100 Grade 1/125В°C |
| TX Power(Max), dBm | 12 |
| Technology | Sub-1 GHz |
| Throughput(Max), Mbps | 0.6 |
Eco Plan
| CC1101QRHBRG4Q1 | |
|---|---|
| RoHS | Compliant |
Application Notes
- DN013 -- Programming output powers on CC1101 (Rev. A)PDF, 238 Kb, Revision: A, File published: Jan 2, 2008
- DN010 -- Close-in Reception with CC1101 (Rev. B)PDF, 102 Kb, Revision: B, File published: Jul 21, 2009
- Resonant Trimming SequencePDF, 88 Kb, File published: Jan 9, 2013
This application report presents an efficient and precise method on how to achieve the desired resonant frequency of configuring the trim array with only a few iterations and measuring the resonant frequency. First, the minimum and maximum resonant frequency is measured; from this data a capacitance gradient is derived, which allows a good prediction of the required capacitance. The calculated cap - DN017 -- CC11xx 868/915 MHz RF Matching (Rev. A)PDF, 328 Kb, Revision: A, File published: Mar 31, 2008
There are three versions of the CC11xx reference design which have been published. This design note gives a short introduction to RF matching and important aspects when designing products using the CC11xx parts and discusses the differences between the three reference design revisions. - AN072 -- Using the TAI-SAW TA0801A SAW Filter and External PA (Rev. A)PDF, 359 Kb, Revision: A, File published: Aug 19, 2009
- AN050 -- Using the CC1101 in the European 868MHz SRD band (Rev. B)PDF, 223 Kb, Revision: B, File published: Sep 11, 2009
- DN501 -- PATABLE Access (Rev. B)PDF, 66 Kb, Revision: B, File published: Mar 24, 2009
- DN500 -- Packet Transmission Basics (Rev. C)PDF, 174 Kb, Revision: C, File published: Apr 6, 2009
- DN503 -- SPI Access (Rev. B)PDF, 94 Kb, Revision: B, File published: Oct 22, 2007
The purpose of this design note is to show how the serial peripheral interface (SPI) must be configured to be able to communicate with the CC1100/CC1101/CC1150/CC2500/CC2550. It also shows how the status bytes should be interpreted and how SW reset is done over the SPI interface. - DN111 - Current Consumption for a Polling Receiver (Rev. A)PDF, 687 Kb, Revision: A, File published: Mar 24, 2009
- DN505 -- RSSI interpretation and timing (Rev. D)PDF, 129 Kb, Revision: D, File published: Jun 16, 2010
- DN506 -- GDO Pin Usage (Rev. A)PDF, 219 Kb, Revision: A, File published: Oct 22, 2007
The purpose of this design note is to explain how to use the different general digital output (GDO) pins for control and monitoring purposes. The focus is set on interfacing with a microcontroller unit (MCU) and is related to the CC1100, CC1101, CC1150, CC2500 and CC2550 devices. - DN005 -- CC11xx Sensitivity versus Frequency Offset and Crystal Accuracy (Rev. C)PDF, 96 Kb, Revision: C, File published: Aug 20, 2009
- DN022 -- CC110x CC111x OOK ASK Register Settings (Rev. E)PDF, 532 Kb, Revision: E, File published: Mar 8, 2012
- DN504 -- FEC Implementation (Rev. A)PDF, 110 Kb, Revision: A, File published: Oct 22, 2007
This design note explains the functionality of forward error correction (FEC) and how it is used in the CC1100, CC1101, CC1110, CC1111, CC1150, CC2500, CC2510, CC2511, and CC2550 devices. Example code for FEC implementation is included. - DN016 -- Compact Antenna Solution for 868/915 MHz (Rev. B)PDF, 832 Kb, Revision: B, File published: Aug 20, 2009
- DN502 -- CRC Implementation (Rev. D)PDF, 55 Kb, Revision: D, File published: Oct 27, 2009
- DN024 -- 868 MHz, 915 MHz and 955 MHz Monopole PCB Antenna (Rev. E)PDF, 1.0 Mb, Revision: E, File published: Feb 22, 2013
- DN033 - Mitsubishi Ceramic Antenna for 868 MHz, 915 MHz & 955 (Rev. A)PDF, 685 Kb, Revision: A, File published: Sep 14, 2010
- DN023 -- 868 MHz, 915 MHz and 955 MHz Inverted F Antenna (Rev. C)PDF, 369 Kb, Revision: C, File published: Aug 30, 2011
Model Line
Series: CC1101-Q1 (1)
Manufacturer's Classification
- Semiconductors> Wireless Connectivity> Companion Wireless Solutions> Smart RF Transceivers
